The most common cause for streaking, splotchy areas, or patches of discolored surface in a recently Rejuvenated floor is residue from a previous product, wax or oil that is interfering with the Rejuvenate. The best way to avoid this issue is to follow the clean and prep guidelines before applying Rejuvenate.

Another major cause for a streaked finish is the improper application of Rejuvenate. Overworking the same area while Rejuvenate is wet, applying in a circular, side to side motion, heavily overlapping strokes or mopping against the grain can all cause streaking. For a streak free finish be sure to follow the Restorer Application Guidelines.

Be sure that your microfiber bonnet is clean and doesn't have dirt or other material stuck in the fibers. This is another common causefor streaking.

Light streaking can sometimes be fixed by applying an additional coat to the surface. If additional coats do not start to minimize or remove streaking then removing the Rejuvenate and re-applying may be necessary.

To remedy stuborn streaking, Rejuvenate Restorer must be removed and re-applied. If there is any residual product, wax or oil under the Rejuvenate, the offending residue must be cleaned off as well. (Please refer to that brand's removal instructions.) Once the residue is removed, Rejuvenate can bond properly to the surface and you will get a proper finish. Follow this guide to remove Rejuvenate Restorer.

Items needed to remove Rejuvenate Restorer:

Bottle of AMMONIA FREE glass cleaner like Windex Crystal Rain

Nylon sponge, mesh scrubber or non-abrasive/light weight scour pad

Clean microfiber mop bonnet & a sponge mop

Directions for removal:

Spray an even coat of ammonia free glass cleaner onto a 4 foot by 4 foot area of the surface where Rejuvenate is to be removed.

Allow the cleaner to settle and react with Rejuvenate for no more than 5 minutes. DO NOT apply so much of the ammonia free glass cleaner that it forms puddles if you are working with wood surfaces. Excessive liquids of any kind can warp and/or damage wood surface.

After 5 minutes, you will begin to see a slightly milky color develop. This is expected and means the Crystal Rain is reacting with the Rejuvenate. If you rub the surface with your finger you should feel the Rejuvenate pilling up and lifting from the surface. You can slowly agitate the surface with your fingers or the scrubber to try and speed up the process. You can add more Crystal Rain to the surface sparingly while you are agitating the surface.

If possible, attach the scrubber to the head of the mop to facilitate cleaning. Some mops have clips to hold the scrubber in place and some pads can be slipped over the entire mop head.

Dampen the scrubber and scrub the previously prepared 4 foot by 4 foot area. You can apply ample pressure as though you were cleaning dried liquid, however do not apply so much pressure that you scratch the surface. The amount of cleaner and pressure needed can vary depending on amount of coats and/or how long the surface has been Rejuvenated.

Once the entire 4 foot by 4 foot area has been scrubbed, dry mop the area using a clean, dry Microfiber Bonnet or towel to remove any residue from the Rejuvenate and/or Remover.

Repeat steps until your entire surface has been completed.

Once finished, clean the floor using the Rejuvenate Floor Cleaner according to the directions on the bottle.

Allow the floor to dry completely before re-applying Rejuvenate Floor Restorer.

Do's & Don'ts

DO clean one small area at a time

DO allow ammonia free glass cleaner to react with the Rejuvenate before scrubbing

DO repeat steps as needed

DO NOT apply excessive amounts of ammonia free cleaner to wood surfaces
DO NOT apply excessive force when scrubbing wood surfaces
DO NOT use a glass cleaner with ammonia in it

IMPORTANT: Rejuvenate Professional is a Urethane based product and can not be removed using the directions above. Click here for Professional Removal instructions